Buy The Fuel Mule Now!!!31 Tips for Saving Gas and MoneyInstructions for installing The Fuel MuleLearn more about The Fuel Mule and how it works


Assembly Instructions

Fuel Mule Unit:

We now are manufacturing a device that works on gasoline engines, diesel powered engines and furnaces that are fueled with fuel oil, natural gas or propane.  Our Fuel Mule, fuel saving device attaches to the steel or rubber fuel line supplying your gas or diesel engine or furnace. The Fuel Mule, fuel device aligns the electrons in the molecules of the atoms allowing the fuel to burn more efficiently. The fuel burning more efficiently allows the engine or furnace to work less. Emissions are reduced up to 30%. You could be using up to 30% less fuel. The fuel savings will more than pay for the cost of The Fuel Mule device in a short time. There are no changes made to the engine or the furnace.  Do not alter the engine or furnace. The installation can be done in 10 minutes or less. The Fuel Mule device will clamp onto the existing fuel line as seen in the picture below. The fuel line is not cut or disturbed. The Fuel Mule device will last many years with no maintenance. The Fuel Mule is made of stainless steel and will not deteriorate.

Benefits:
“The Fuel Mule” Fuel Saving Units (Patent Pending)

  • Save up to 30% in fuel
  • The Fuel Mule will last many years with no maintenance
  • The Fuel Mule is made from stainless steel
  • The Fuel Mule utilizes proven technology that will work on any propane, natural gas or fuel oil furnace or any gas or diesel engine
  • 100% satisfaction guaranteed with 90 day money back guarantee
  • Furnace, gas engines and diesel engines will operate more efficiently, saving you money
  • The Fuel Mule furnace unit will provide the same heat using less fuel
  • The emissions will be much cleaner, causing the combustion area of the furnace or the engine to remain cleaner and last longer
  • On engines The Fuel Mule will increase the miles per gallon of fuel, and provide more power, especially up and down steep grades
  • Your vehicle will run smoother, and run at the same speed using less fuel
  • The engine oil, fuel injectors and the exhaust emissions will stay cleaner longer
  • The Fuel Mule is made in the USA

Assembly  Instructions must be read twice!     

(1) Check the parts – You will have the following:

  • Two Fuel Mule sub-assemblies
  • Four 1/4 - 20 self-locking nuts
  • Four 1/4 - 20 hex head
  • Two plastic ties   

       Tools Required:

  • 7/16 Box End Wrench
  • Ratchet Socket Wrench with a 7/16 Socket
  • Side-cut Pliers for cutting the Plastic Ties

                                        

(2) Clamp The Fuel Mule onto the fuel line as seen in the picture.  When The Fuel Mule is shipped, the two halves are attracted to each other and are parallel to each other.  When you install The Fuel Mule, REVERSE the top half, such that the two units repel each other.  When installed, the two halves must repel each other.  THE ENDS WITH THE ARROWS MUST POINT TOWARDS THE ENGINE OR FURNACE.  If arrows are missing, use a compass and install the ends that check North, towards the engine or furnace.  BE SURE TO POSITION The Fuel Mule SUCH THAT THE FUEL SUPPLY LINE IS IN THE CENTER GROOVE OF The Fuel Mule DEVICE.  THE SUPPLY LINE IS THE ONE THAT HAS THE FUEL FILTER ON IT.  The Fuel Mule WILL NOT WORK IF THE SUPPLY LINE IS NOT IN THE CENTER GROOVE.  The Fuel Mule WORKS BEST WHEN THE UNIT IS VERY CLOSE TO THE COMBUSTION AREA OF THE ENGINE.  WE RECOMMEND THAT YOU INSTALL The Fuel Mule UNDER THE VEHICLE, JUST BEFORE THE FUEL LINES GO UP INTO THE ENGINE.

Gasoline Engines:  The Fuel Mule is to be clamped on the steel or rubber fuel supply line as near the engine as possible without being actually on the engine.  The Fuel Mule must clamp on the fuel supply line going to the engine.  WARNING:  Keep away from computer and computer chips on the engine or vehicle a minimum of 8 inches.  The plastic ties are used as necessary to secure The Fuel Mule unit.  The Fuel Mule must be secure.  Use the plastic ties to secure it to something that is fixed, secure and solid.  The Fuel Mule must be solid, do not leave it loose to rub or rattle.  The fuel line must be secure.  WARNING: Before and while installing the The Fuel Mule, always keep the The Fuel Mule away from all computers or anything that has any computer memory.  Engines are set up in many different ways.  Install The Fuel Mule as close to the engine as possible.  An existing electrical device that is between The Fuel Mule and the engine may interfere with The Fuel Mule operation.  If this is the case then move The Fuel Mule closer to the engine, after the electrical device.  When you fill up your fuel tank, record the mileage on your speedometer and the gallons of fuel that you put into your tank.  After you have filled the fuel tank a few times, compare the miles per gallon information with the information that you have from before you installed The Fuel Mule unit.  This will show you your miles per gallon fuel savings.  Should you not want to install The Fuel Mule on your vehicle yourself, then have a reliable auto mechanic do it for you.  
WARNING: Never ever install The Fuel Mule on any type of aircraft.